TITANIC T-90 FLASH FILE SP7731G 6 READ BY CM2 100% TESTED FLASH BY CM2

 Wait for device ... 

Device Connected!

BootVersion : SPRD3

Boot : INF : 0_SC7731x_BASE : SC7731G_eMMC_1GB_NS

Sending Init Boot ... 

Boot sent!

Kick FDL ... 

Kick FDL again ... 

BootVersion : Spreadtrum Boot Block version 1.1

Protocol setup ... 

Port speed : 921600

Sending Flash Boot ... 

Boot sent!

Kick FLASH FDL ... 

ProtoEx :  : TRCC not supported!

FDL : Control transfered!

Boot Done!

Device info : 

Patch Level    : MRA58K

Display ID     : X98_S5_J106G_TITANIC_T-90_B1B8_V001_20200712

Ver. Incmt     : root-103233

Ver. CodeName  : REL

Ver. Release   : 6.0

Sec. Patch     : 2016-07-01

Build Time     : 1594546736

Product Brand  : TITANIC

Product Name   : sp7731g_1h10_hd_oversea

Product Device : sp7731g_1h10

Product Board  : sp7731gea_hdr

Product Manfct : TITANIC

Board Platform : sc8830

Product Info   : sp7731g_1h10

Product Model  : T-90

AndroidVer : 6

VlnrLevel : 0x01

SC8830__TITANIC__T-90__6.0__X98_S5_J106G_TITANIC_T-90_B1B8_V001_20200712__MRA58K__sp7731g_1h10

Read : prodnv.img

ExtSparse : Compression ratio : 86%

Read : phase.cfg

Read : wmodem.bin

Read : wdsp.bin

Read : wnvitem.bin

Read : modem_wcn.img

Read : wcnnvitem.bin

Read : boot_logo.bmp

Read : fastboot_logo.bmp

Read : logo2.bin

Read : logo3.bin

Read : logo4.bin

Read : logo5.bin

Read : boot.img

Read : system.img

ExtSparse : Compression ratio : 87%

Make : persist.img

Read : sysinfo.bin

ExtSparse : Compression ratio : 4%

Make : cache.img

Read : recovery.img

Make : userdata.img

Read : u-boot.bin

Read : u-boot-spl.bin

Firmware size : 0x49AE9FB8 ( 1.15 GiB )

Android Info saved : _Android_info.txt

Reconnect Power/Cable!

Done!

Elapsed: 00:06:31

Redmi Note 5 DUMP FILE 512MB READ BY UFI BOX

 Connection status: XHCI:HUB3:[#0]:USB 2.00 High-Speed

Interface: UFI High-Speed

Serial number: 0011-8842-5443

 Boot version: 1.05, FW version: 1.13 (Aug 19 2019 23:46:09)

Insertion test... Done

Init bus...

VCC: 3.3 V, VCCQ: 3.0 V

Bus: 8 bit (HS SDR 24MHz)

Access mode: sector mode

Power supply: dual-voltage (1.70-1.95V, 2.7-3.6V)

 Card/BGA: BGA (Discrete embedded) - High density MMC

 Manufacturer ID: 0x90 (SK Hynix)

 Product name: HCG8a4 (0x484347386134), rev: 0xA2, serial number: 0x0AE9E07F

 Manufacturing date: Apr 2018

CID: 90014A48 43473861 34A20AE9 E07F45E8

CSD: D0270132 8F5903FF FFFFFFEF 8A400026

EXT_CSD revision: 1.8 (MMC v5.1) 

Partition info:

 Boot1: 4 MiB

 Boot2: 4 MiB

 RPMB: 4 MiB [Provisioned, counter: 50432]

 User area: 58.24 GiB(62,537,072,640 bytes)

Cache size: 1 MiB

Hardware reset function: 1

Partition configuration: 0x00

 No boot acknowledge is sent (default)

 Device is not boot-enabled (default)

Partitioning support: 0x07

 Device support partitioning feature

 Device can have enhanced technological features

 Device partitioning possible

Boot configuration protection: 0x00

Boot bus conditions: 0x00

Boot area write protection: 0x00

   note5dump

ANDROID System Info:

 platform: sdm660, cpu abi: arm64-v8a

 manufacturer: Xiaomi

 board: sdm636, name: whyred

 brand: xiaomi, model: Redmi Note 5

 build model list: Redmi Note 5

 build id: PKQ1.180904.001, version: 9 [Pie] (PKQ1.180904.001)

 build description: whyred-user 9 PKQ1.180904.001 V11.0.3.0.PEIMIXM release-keys

 

SAMSUNG SM-G530FZ DUMP FILE READ BY UFI & READ BY EASY JTAG PLUS 512 mb

 READ BY UFI

VCC: 3.3 V, VCCQ: 1.8 V

Bus: 1 bit (SDR 24MHz)

Access mode: sector mode

Power supply: dual-voltage (1.70-1.95V, 2.7-3.6V)

 Card/BGA: BGA (Discrete embedded) - High density MMC

 Manufacturer ID: 0xFE (Micron)

 Product name: P1J95K (0x50314a39354b), rev: 0x13, serial number: 0x0C83BE1C

 Manufacturing date: Apr 2015

CID: FE014E50 314A3935 4B130C83 BE1C4238

CSD: D06E0132 0F5913FF FFFFFFEF 92400070

EXT_CSD revision: 1.6 (MMC v4.5, v4.51) 

Partition info:

 Boot1: 2 MiB

 Boot2: 2 MiB

 RPMB: 2 MiB [Provisioned, counter: 29]

 User area: 7.28 GiB(7,818,182,656 bytes)

Cache size: 256 KiB

Partition configuration: 0x00

 No boot acknowledge is sent (default)

 Device is not boot-enabled (default)

Partitioning support: 0x07

 Device support partitioning feature

 Device can have enhanced technological features

 Device partitioning possible

Boot configuration protection: 0x00

Boot bus conditions: 0x00

Boot area write protection: 0x00

ANDROID System Info:

 platform: msm8916, cpu abi: armeabi-v7a

 manufacturer: samsung

 board: MSM8916, name: grandprimeltexx

 brand: samsung, model: SM-G530FZ

 build model list: SM-G530FZ

 build id: KTU84P, version: 4.4.4 [Lollipop] (KTU84P.G530FZXXU1AOA6)

 build description: grandprimeltexx-user 4.4.4 KTU84P G530FZXXU1AOA6 release-keys

Internal storage: 5.34 GiB

crypto state: unencrypted

Selected: [Micron] (JWA60)MT29TZZZ8D5BKFAH-125W/8GB   (BGA221)

READ BY EASY JTAG PLUS

Setting interface to EasyJtag2/ISP_HiPower

Setting bus width to 1 Bit

HiPower mode is ON

Setting frequence to 36 MHz

CMD Pullup Level: 1713 mV

CMD Active Level: 1772 mV

EMMC Device Information :

EMMC CID: FE014E50314A39354B130C83BE1C4239

EMMC CSD: D06E01320F5913FFFFFFFFEF92400071

EMMC Manufacture : MICRON , EMMC NAME: P1J95K , HEX: 50314A39354B , S/N: 0C83BE1C , rev. 0x13

EMMC Manufacture ID: 0xFE , OEM ID: 0x4E , Device Type: BGA (Discrete embedded) , Date: 4/2015

   EMMC ROM 1 (Main User Data) Capacity: 7456 MB (0001D2000000)

   EMMC ROM 2/3 (Boot Partition 1/2) Capacity: 2048 KB (000000200000)

   EMMC RPMB (Replay Protected Memory Block) Capacity: 2048 KB (000000200000) Counter: 29 , Response: Not Clean

EMMC Permanent Write Protection: No

EMMC Temporary Write Protection: No

Extended CSD Information :

Extended CSD rev: 1.6 (MMC 4.5, MMC 4.51)

Boot configuration [PARTITION_CONFIG]: 0x00 , Boot from: no boot

Boot Bus Config: 0x00 , width 1bit

H/W Reset Function [RST_N_FUNCTION]: 0x00, RST_n signal is temporarily disabled

Supported partition features [PARTITIONING_SUPPORT]: 0x07

Device supports partitioning features

Device can have enhanced technological features in partitions and user data area

Device can have extended partitions attribute

Partition Settings [PARTITION_SETTING_COMPLETED]: 0x00

Backup saved: P1J95K_0C83BE1C_20210422_135756.extcsd

EMMC Init completed.

Get firmware version

sm-g520fzdumpfile

Brand = samsung

Manufacturer = samsung

Device = grandprimelte

Model = SM-G530FZ

Phone platform = msm8916

CPU Abi = armeabi-v7a

Android release = 4.4.4

Firmware version = KTU84P.G530FZXXU1AOA6

Firmware date = Fri Jan 23 17:04:31 KST 2015

 

Walton Primo EM2 8.1 Flah File (SPD 9850) Without Password 1000% Tested Care Firmware

 

MYCELL SPIDER V10 FLASH FILE | MT6580 5.1 CM2 READ FIRMWARE

 xGPT : Normalize settings Ok!

Brand     : SPIDER V10

ProdName  : SPIDER V10

ProdModel : U2

Device    : SPIDER V10

AndroidVer: 5.1

MTKxCPU   : MT6580

MTKxPRJ   : ALPS.L1.MP6.V2_YUANDA6580.WE.L

[Read Ok] : preloader_yuanda6580_we_l.bin

[Read Ok] : lk.bin

[Read Ok] : boot.img

[Read Ok] : recovery.img

[Read Ok] : logo.bin

[Read Ok] : secro.img

[Read Ok] : system.img

[Read Ok] : cache.img

[Read Ok] : userdata.img

[ScatCFG] : MT6580 / V1.1.2 / yuanda6580_we_l / EMMC

Android Info saved

MAUI Meta DB saved

HWConfig Info saved

FW Size : 1437 MiB

Scatter saved to : C:\Users\GSM YOUSUF\Desktop\MT6580__SPIDER_V10__U2__SPIDER_V10__5.1__ALPS.L1.MP6.V2_YUANDA6580.WE.L\

All done!

Done!

Elapsed: 00:06:37

Reconnect Power/Cable!

OPPO A3S DUMP FILE BY UFI BOX 512MB

  Connection status: XHCI:HUB3:[#0]:USB 2.00 High-Speed

Interface: UFI High-Speed

Serial number: 0011-8842-5443

 Boot version: 1.05, FW version: 1.13 (Aug 19 2019 23:46:09)

Insertion test... Done

Init bus...

VCC: 3.3 V, VCCQ: 1.8 V

Bus: 1 bit (SDR 4MHz)

Access mode: sector mode

Power supply: dual-voltage (1.70-1.95V, 2.7-3.6V)

 Card/BGA: BGA (Discrete embedded) - High density MMC

 Manufacturer ID: 0x15 (Samsung)

 Product name: QE63MB (0x514536334d42), rev: 0x03, serial number: 0x766206AE

 Manufacturing date: Sep 2018

CID: 15010051 4536334D 42037662 06AE9516

CSD: D0270132 0F5903FF F6DBFFEF 8E40400C

EXT_CSD revision: 1.8 (MMC v5.1) 

Partition info:

 Boot1: 4 MiB

 Boot2: 4 MiB

 RPMB: 4 MiB [Provisioned, counter: 126450]

 User area: 14.56 GiB(15,634,268,160 bytes)

Cache size: 64 MiB

Hardware reset function: 1

Partition configuration: 0x38

 No boot acknowledge is sent (default)

 User area is enabled for boot

Partitioning support: 0x07

 Device support partitioning feature

 Device can have enhanced technological features

 Device partitioning possible

Boot configuration protection: 0x00

Boot bus conditions: 0x00

Boot area write protection: 0x00

ANDROID System Info:

 platform: msm8953, cpu abi: arm64-v8a

 manufacturer: OPPO

 board: msm8953, name: CPH1803

 brand: OPPO, model: CPH1803 (OPPO A3s)

 build model list: CPH1803 (OPPO A3s)

 build id: OPM1.171019.026, version: 8.1.0 [Oreo] (CPH1803EX_11_A.34)

 build description: msm8953_64-user 8.1.0 OPM1.171019.026 eng.root.20210122.143520 release-keys

crypto state: encrypted?

Custom moviNAND command is not supported for this device(MMC51).

Selected: [SAMSUNG] KMQE60013M-B318/16GB+LPDDR3 16Gb   (BGA221)

SYMPHONY V98 DUMP FILE UFI BOX

 Init bus...

VCC: 3.3 V, VCCQ: 3.0 V

Bus: 8 bit (HS SDR 24MHz)

Access mode: sector mode

Power supply: dual-voltage (1.70-1.95V, 2.7-3.6V)

 Card/BGA: BGA (Discrete embedded) - High density MMC

 Manufacturer ID: 0x88 (Foresee)

 Product name: EPB100 (0x455042313030), rev: 0x49, serial number: 0x5BD56903

 Manufacturing date: Jul 2018

CID: 88010345 50423130 30495BD5 6903750E

CSD: D0FFFF32 0F5903FF FFFFFFE7 964000EA

EXT_CSD revision: 1.7 (MMC v5.0, v5.01) 

Partition info:

 Boot1: 4 MiB

 Boot2: 4 MiB

 RPMB: 4 MiB [Provisioned, counter: 4186]

 User area: 7.22 GiB(7,752,122,368 bytes)

ANDROID System Info:

 platform: sp7731e, cpu abi: 

 board: k121, name: V98

 brand: Symphony, model: V98

 build id: , version: 8.1.0 [Oreo] ()

crypto state: encrypted?

Preset sets to 1.95 GiB (exclude userdata)